Backlight bleed and IPS glow
How to tell bleed from glow, what is normal on a new screen, and what to check before a return.
Why a black screen isn't black
Most flat screens are a layer of liquid crystal in front of a light. The crystal layer blocks the light where the picture is dark and lets it through where it's bright. Blocking is never perfect, so a black screen is really a very dark grey, and the places where blocking is weakest show up as patches of light.
Two different effects cause these patches, and they're easy to confuse. Backlight bleed is light leaking around the edges of the crystal layer, usually where the panel is pressed into its frame. IPS glow is light scattering off the crystal itself, and it belongs to a whole family of panels rather than to a faulty one. Knowing which you have decides whether you have a complaint.
Setting up the test
The backlight bleed test fills the screen with black, white, a near-black grey, a dark grey, then red, green and blue. Bleed and glow show on the black and near-black fields. Darken the room, turn the brightness up, and sit at your normal distance, square on to the screen.
Start with the brightness you really use. Full brightness in a pitch-black room shows more leak than you'll ever see in use, and that is how most alarming photos come about. Judge the screen as you use it, then push the brightness up to see the worst case.
Telling them apart
Move your head: glow changes with the angle, bleed does not.
IPS glow changes as your viewing angle changes. Sit dead centre and it fades; lean to one side and the opposite corner brightens, often with a faint warm or cool tint. It usually sits in the corners, looks like a soft haze rather than a shape, and spreads over a wide area. Move away from the screen and it shrinks.
Backlight bleed stays put. It's light coming through a gap, so it looks the same from every angle. It tends to sit along an edge or in one spot near the frame, with a brighter core and a fairly clear shape: a wedge from a corner, a bar along the bottom, a blob where a clip presses the panel. Pressing the frame gently near it can make it change shape, which is a sign the frame is pinching the panel.
A quick comparison:
- Glow fades when you move to the centre; bleed doesn't.
- Glow is diffuse and corner-shaped; bleed has edges and a bright core.
- Glow is even across the four corners on a good panel; bleed is lopsided.
- Glow shrinks as you move back; bleed looks the same size.
What's normal
Some glow is normal on any panel of this type, and no amount of returning will get you a unit without it. What varies is how much. A good panel shows a faint, even haze in the corners that you forget about in daily use; a poor one shows a strong yellow or silver glow that's visible on dark scenes with the lights on.
A small amount of bleed is also common, especially on larger and cheaper screens, where the frame has more panel to hold. If you can only find it on the black field, in a dark room, at full brightness, it's unlikely to bother you in use. Bleed that you can see on the dark grey field, or on a dark scene in a film with a lamp on, is the kind that nags.
The browser can't measure any of this: it only draws the fields, and you judge them by eye. Photos exaggerate both bleed and glow, because a camera's exposure stretches the difference between black and near-black. Judge by eye, not by photo.
What to check before a return
Sellers and manufacturers rarely publish a bleed figure, and this site measures none, so whether to return a screen is your call. Points people weigh before deciding:
- Whether the bleed shows in ordinary use: on the dark grey field at normal brightness, on dark film scenes with the room lit, or in a letterboxed picture's black bars.
- Whether it is lopsided, with one corner or edge far worse than the others, or moves when you press the frame, which points to the frame rather than the panel's nature.
- Whether what bothers you is glow, which a replacement of the same panel type will have too; a different panel type, with deeper blacks, is the change that removes it.
Before you decide, check the obvious. Let the screen warm up; some bleed eases as the panel settles in. Make sure the stand or a wall mount isn't twisting the frame. Then ask whether it bothers you in use, not whether a test can find it.
Where to look next
The same solid fields show other faults. The white and grey fields show darker patches and tints; the red, green and blue fields show stuck pixels, and a dot that stays black on every colour is a dead one. The stuck pixel fixer and our guide on stuck versus dead pixels take it from there.